How to Clean and Maintain Rollex Building Products
Rollex siding and soffit require very little maintenance. Under normal weather conditions, an occasional cleaning with a graden hose using clear, fresh water will remove loose soil and dirt.


  • Aluminum Products

  • Steel Products


    • Aluminum Products

    Moderate/Heavy Dirt Accumulation    		 (Back to Top)

    Periodic cleaning may be necessary where an unusual amount of dirt is deposited on siding surfaces, under eaves or other protected areas. Use the following simple cleaning procedures as often as conditions dictate.

    For surface soil or stains from industrial fallout, tree sap, insecticides, chimney fumes, etc. use an ordinary non-abrasive household detergent. One-third cup of mild detergent (Example: Tide) plus 2/3 cup of a household cleaner (Example: Soilax) to one gallon of water is recommended. Use a soft rag, sponge, or soft bristle brush with gentle rubbing action. DO NOT RUB VIGOROUSLY––this can cause glossy areas over the finish. A rotary soft bristle brush equipped with an extension handle is useful to reach higher areas. Wash the house from top to bottom to minimize streaking. Immediately rinse all washed surfaces with a garden hose.

    Mildew
    In some locations, mildew may be an issue. It appears as black spots on the surface and is usually first detected under eaves, in porch enclosures and other areas protected from rainfall. To remove, prepare a solution as follows and use the washing and rinsing instructions outlined above:

  • 1/3 Cup Detergent (Example: Tide)
  • 2/3 Cup Household Cleaner (Example: Soilax)
  • 1 Qt. 5% Sodium Hypochlorite* (Example: Clorox)
  • 3 Qt. Water

    • * CAUTION: GREATER CONCENTRATIONS MAY CAUSE DAMAGE TO THE SIDING FINISH. AVOID EYE AND SKIN CONTACT. FOLLOW PREVIOUS INSTRUCTIONS FOR CLEANING AND RINSING.

    Stains
    Stains from tar, caulking or similar materials may be removed using mineral spirits, then rinsing thoroughly with water. Avoid use of abrasive cleaners and strong solvents. Test all cleaning solutions on an inconspicuous surface before applying to broader areas.

    This care and maintenance information is intended to be of assistance. Rollex assumes no responsibility for mixing and application procedures beyond its control.
    Steel Products

    Moderate/Heavy Dirt Accumulation    		 (Back to Top)

    For surface soil or stains from industrial fallout, tree sap, insecticides, chimney fumes, etc. use an ordinary non-abrasive household detergent. One-third cup of mild detergent (Example: Tide) plus 2/3 cup of a household cleaner (Example: Soilax) to one gallon of water is recommended. Use a soft rag, sponge, or soft bristle brush with gentle rubbing action. DO NOT RUB VIGOROUSLY––this can cause glossy areas over the finish. A rotary soft bristle brush equipped with an extension handle is useful to reach higher areas. Wash the house from top to bottom to minimize streaking. Immediately rinse all washed surfaces with a garden hose.

    Mildew
    In some locations, mildew may be an issue. It appears as black spots on the surface and is usually first detected under eaves, in porch enclosures and other areas protected from rainfall. To remove, prepare a solution as follows and use the washing and rinsing instructions outlined above:

  • 1/3 Cup Detergent (Example: Tide)
  • 2/3 Cup Household Cleaner (Example: Soilax)
  • 1 Qt. 5% Sodium Hypochlorite* (Example: Clorox)
  • 3 Qt. Water

    • * CAUTION: GREATER CONCENTRATIONS MAY CAUSE DAMAGE TO THE SIDING FINISH. AVOID EYE AND SKIN CONTACT. FOLLOW PREVIOUS INSTRUCTIONS FOR CLEANING AND RINSING.

    Stains
    If stains cannot be removed by normal household detergents, request a special siding cleaner from your siding contractor. CAUTION: DO NOT USE ABRASIVE OR SOLVENT TYPE CLEANERS OR PAINT REMOVER. THESE MATERIALS MAY SOFTEN OR ACTUALLY REMOVE YOUR SIDING FINISH. WHEN USING ANY CHEMICAL AGENTS, OBSERVE MANUFACTURER'S SAFETY PRECAUTIONS AND AVOID EYE AND SKIN CONTACT.

    Test all cleaning solutions on an inconspicuous surface before applying to broader areas.

    This care and maintenance information is intended to be of assistance. Rollex assumes no responsibility for mixing and application procedures beyond its control.